Whirlpool Fault Codes - Turners Timer Repair

Polara

Fault Code	Condition/Description	Resolution
F1 F0	EEPROM communication error	Repair Electronic Range Control (ERC)
F1 E1	EEPROM checksum error	Repair Electronic Range Control (ERC)
F1 E2	UL A/D errors	Repair Electronic Range Control (ERC)
F1 E4	Model ID error	Reinsert key tail. If not corrected, repair control
F1 E6	Latch signal mismatch error	Repair Electronic Range Control (ERC)
F2 E0	Shorted key error	Replace keypad assembly
F2 E1	Key tail unplugged	Reinsert key tail
F3 E0	Top oven sensor open	Check for open circuit. Sensor resistance should be 1K to 1.1K @ room temperature. If not, replace the sensor
F3 E1	Top oven shorted	Check for shorted sensor circuit, otherwise replace sensor
F3 E2	Bake range over temperature	At room temperature, sensor resistance should be 1K to 1.1K. If not, replace the sensor. If the sensor checks okay, repair Electronic Range Control (ERC)
F3 E3	Clean range over temperature	At room temperature, sensor resistance should be 1K to 1.1K. If not, replace the sensor. If the sensor checks okay, repair Electronic Range Control (ERC)
F3 E4	Bottom oven sensor open	Check for open circuit. Sensor resistance should be 1K to 1.1K @ room temperature. If not, replace the sensor
F3 E5	Bottom oven sensor shorted	Check for shorted sensor circuit, otherwise replace sensor
F5 E0	Door switches do not agree	Check door switch. Contacts should be closed when plunger is actuated. Check door switch circuit for open
F5 E1	Door latch not operating	Check that door switch is completely closed. Check latch, solenoid, and actuation switch for electrical or mechanical malfunction
F8 E0	Refrigeration not operating properly	Check for open circuit between control and refrigeration cooling module
PF	Power failure (not a failure mode)	Do not replace Electronic Range Control (ERC)

4-Digit Failure Code

Fault Code	Condition/Description	Resolution
F1 – E1	Safety flip flop	Repair Electronic Range Control (ERC)
F2 – E0	Shorted keypad	Replace keypad
F3 – E0	Oven temperature sensor opened	Replace oven temperature sensor
F3 – E1	Oven temperature sensor shorted	Replace oven temperature sensor
F3 – E2	Oven too hot	Replace oven temperature sensor
F3 – E3	Clean temp too hot	Replace oven temperature sensor
F5 – E0 F5 – E1 F5 – E2	Check door/latch switch	Replace switch if defective

2-Digit Failure Code

Fault Code	Condition/Description	Resolution
F1	Analog to Digital Failure	Disconnect for 30 seconds – if display reappears repair Electronic Range Control (ERC)
F1	Safety flip flop	Repair Electronic Range Control (ERC)
F1	Shorted keypad	Replace keypad
F3	Oven temperature sensor opened	Replace oven temperature sensor
F2	Oven temperature sensor shorted	Replace oven temperature sensor
F3	Oven too hot	Replace oven temperature sensor
F3	Clean temp too hot	Replace oven temperature sensor
F5	Check door/latch switch	Replace switch if defective

P30” Free-standing Range/Stove Oven, SF3…& 24” Built-In

Fault Code	Condition/Description	Resolution
F2	Oven temperature above specifications	8-pin connector oven temperature sensor to the Electronic Range Control
F3	Open oven temperature sensor	Inspect wiring harness, recommended to replace oven temperature sensor if needed
F4	Shorted oven temperature sensor	Inspect wiring harness, recommended to replace oven temperature sensor if needed
F5	Pushbutton jammed	Inspect for binding of pushbuttons and control panel glass. If everything is good, recommended to replace touch panel
F6	Computer logic interrupted	Repair Electronic Range Control (ERC)
F7	Computer logic interrupted	Repair Electronic Range Control (ERC)
F8	Computer logic interrupted	Repair Electronic Range Control (ERC)