Frigidaire Fault Codes - Turners Timer Repair

Fault Codes Version 2

Fault Code	Condition/Description	Resolution
F0 & F1	EOC (Electronic Oven Control) failure	Repair the EOC (Electronic Oven Control)
F2	Oven too hot	Check Bake function
F3	Oven temperature sensor open	Check oven temperature sensor, 1100 ohms
F4	Oven temperature sensor shorted	Replace temperature sensor
F5, 6, 7	EOC (Electronic Oven Control) failure	Repair the EOC (Electronic Oven Control)
F8	Lock switches	Check or Replace door lock

Fault Codes Version 3

Fault Code	Condition/Description	Resolution
F0 & F1	EOC (Electronic Oven Control) failure	Repair EOC (Electronic Oven Control)
F2	Oven too hot	Likely a bad oven temperature sensor (should read 1100 ohms) Possible bad EOC (Electronic Oven Control)
F3	Oven temperature sensor open	Replace oven temperature sensor
F4	Oven temperature sensor shorted	Replace oven temperature sensor
F5 or F6 or F7	EOC (Electronic Oven Control) failure	Repair EOC(Electronic Oven Control)

Fault Codes Version 4

Fault Code	Condition/Description	Resolution
F1	Circuit board defective	Repair control board
F2	The oven temperature has risen above 665F and the door is not locked The oven temperature has risen above 965F with the door locked	Check oven temp in mode that failure occurred. Repair EOC (Electronic Oven Control) if above limits Check 8-pin connector. Check and replace oven temperature sensor if necessary
F3	Oven temperature sensor is open (above 3000 ohms)	Check resistance of oven temperature sensor, check for open wiring between oven temperature sensor and control
F4	Oven temperature sensor is shorted (below 500 ohms)	Check resistance of oven temperature sensor, check for shorted wiring between oven temperature sensor and control
F5	Internal watchdog circuit has detected a failure	Repair EOC (Electronic Oven Control)
F6	Shorted buttons	Check push buttons and dome switches on touch pad
F8	Logic interrupted (lock motor switch sequence)	Check door lock switches and wiring

Newer Fault Codes

Fault Code	Condition/Description	Resolution
F10	Control has sensed a runaway temperature condition. Control may have a shorted relay or temperature sensor probe may be bad.	Check temperature sensor probe and replace if necessary. If the oven is overheating, disconnect power. If oven continues to overheat when the power is reapplied, replace the ERC
F11	Shorted keypad: a key has been detected as pressed (for a long period) alarm will terminate all cooking activity	Press clear key. If the fault returns, replace the keyboard. If the problem persists, repair the EOC (Electronic Oven Control)
F12	Bad micro identification	Press clear key. If the fault returns, replace the keyboard. If the problem persists, repair the EOC (Electronic Oven Control)
F13	Bad EEPROM identification/checksum error	Press clear key. If the fault returns, replace the keyboard. If the problem persists, repair the EOC (Electronic Oven Control)
F15	Controller self-check failed	Repair the EOC (Electronic Oven Control)
F20	Control has detected a problem with the communications link	Test harness connections P4 on the EOC (Electronic Oven Control) and P11 ESEC (Surface Element Control Board). If harness is OK then the failure can be caused by a faulty UIB (User Interface Board), ESEC (Surface Element Control Board) or EOC (Electronic Oven Control)
F30	Open temperature sensor probe or wiring problem	Check temperature sensor probe and replace if necessary. If the problem persists, repair the EOC (Electronic Oven Control)
F31	Shorted temperature sensor probe or wiring problem	Check temperature sensor probe and replace if necessary. If the problem persists, repair the EOC (Electronic Oven Control)
F62	Missing zero-cross signal	Repair the EOC (Electronic Oven Control)
F90 F91 F92 F93 F94	Maximum oven door unlock time exceeded. Maximum oven door unlock attempts exceeded Maximum oven door open time exceeded Maximum oven door lock time exceeded Maximum oven door lock attempts exceeded	(F90,91,92,93,94) Check the temperature sensor Check the wiring between the EOC (Electronic Oven Control) and the lock motor micro switch Check to see if lock motor coil or the micro switch is open. If open replace the lock motor assembly Check for binding of the latch cam, lock motor rod and lock motor cam (F92,93,94) Check to see if oven door light switch is open. If it is replace switch
F95	Door motor mechanism failure. The motor does not stop rotating	Check door lock switches and wiring. If they all work than repair the EOC (Electronic Oven Control)